[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: Installation question



When I do a dspsrvpgm httpapir4 I see the following. I know I chose yes.
I suspect if you chose no, you wouldn't see the COMMSSLR4 module, or the
HTTPS exports.

                      Display Service Program Information

                                                                Display
3 of 10
 Service program  . . . . . . . . . . . . :   HTTPAPIR4

   Library  . . . . . . . . . . . . . . . :     DRLIBR

 Owner  . . . . . . . . . . . . . . . . . :   MEDTRON

 Service program attribute  . . . . . . . :   RPGLE

 Detail . . . . . . . . . . . . . . . . . :   *MODULE

 

 Type options, press Enter.

   5=Display description   6=Print description

 

                                          Creation  Optimization  Debug

 Opt  Module      Library     Attribute   Date         Level      Data

      HTTPAPIR4   MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES

      COMPATR4    MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES

      COMMTCPR4   MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES

      HTTPUTILR4  MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES

      ENCODERR4   MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES

      CCSIDR4     MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES

      HEADERR4    MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES

      COMMSSLR4   MSIBETOBJS  RPGLE       08/11/11  *NONE         *YES


                      Display Service Program Information

                                                                Display
5 of 10
 Service program  . . . . . . . . . . . . :   HTTPAPIR4

   Library  . . . . . . . . . . . . . . . :     DRLIBR

 Owner  . . . . . . . . . . . . . . . . . :   MEDTRON

 Service program attribute  . . . . . . . :   RPGLE

 Detail . . . . . . . . . . . . . . . . . :   *PROCEXP

 

                               Procedure Exports:

 

 Procedure Name
ARGOPT
 HTTP_ERROR
*NO   
 HTTPS_INIT
*NO   
 HTTPS_CONNECT
*NO   
 HTTPS_GETRAW
*NO   
 HTTPS_POSTRAW
*NO   
 HTTPS_CLOSE
*NO   
 HTTPS_DCM_REG
*NO   
 HTTP_GETAUTH
*NO   
 HTTP_SETAUTH
*NO   
 HTTP_XPROC
*NO   

-----Original Message-----
From: ftpapi-bounces@xxxxxxxxxxxxxxxxxxxxxx
[mailto:ftpapi-bounces@xxxxxxxxxxxxxxxxxxxxxx] On Behalf Of Tom Thomson
Sent: Wednesday, February 13, 2013 9:45 AM
To: ftpapi@xxxxxxxxxxxxxxxxxxxxxx
Subject: Installation question

Hello,

 

I am getting log entry saying "Only the http protocol is available" when
I call a webservice via https//.  Searched the archives and found this
is likely an installation problem where the install question, "Would you
like to build HTTPAPI with SSL support?" was answered "no".  Is there a
way to verify HTTPAPI was installed with/without SSL support?

 

Regards,

-Tom

 

  

 




Kevin Bucknum
Senior Programmer Analyst
MEDDATA/MEDTRON
Tel: 985-893-2550
 
-----------------------------------------------------------------------
This is the FTPAPI mailing list.  To unsubscribe, please go to:
http://www.scottklement.com/mailman/listinfo/ftpapi
-----------------------------------------------------------------------